Installation Instructions for Catalog No.
B-KHP-8010-N5
Description
The Edwards B-KHP-8010-N5 Phone Horn is a solid state,
self-contained unit powered by 120V 60 Hz. The unit is
activated by AC or DC voltage through solid state relays.
The Phone Horn is designed for use in indoor and outdoor
areas that have medium ambient noise level such as ware-
houses, construction sites, garages and car lots. The unit
is rated at 104 dB at 10 feet (3.05m). The phone horn is UL
listed and comes with strain relief, weatherproof connec-
tors for securing the 6 foot (1.83m) power cord and tele-
phone line to the housing.
• These devices are intended for connection to single
line telephone or key systems only. They are not
intended for use on "party line" or on coin operated
telephone lines.
• When installed in accordance with these instructions,
the devices can be readily disconnected without
affecting equipment remaining on the telephone
network.
• Registered with the Federal Communications
Commission in compliance with Part 68 of FCC Rules
and Regulations.
• UL Listed Type NM (non-monitored) signal device
Important Telephone Information
The following information may be required by the tele-
phone company: Telephone Number, FCC Registration
Number: 3Z9USA-21250-RG-N, Ringer Equivalence Number
(REN): 1.5B at greater then 50 Volts and 3.4B at less than
50 Volts.
The REN allows the installer to determine the number of
devices that can be added to the telephone line and still
have all the devices ring when the number is called. In
most, but not all, areas, the sum of all RENs for all devices
connected to your line should not exceed five. To be sure
of the number of devices you can connect to your tele-
phone line, contact your local telephone company.
If these devices damage the telephone network, the tele-
phone company will notify the owner that it may tempo-
rarily disconnect service if they consider such action nec-
essary. If the owner considers the disconnection unwar-
ranted, they have the right to bring a complaint to the
FCC.
The telephone company may make changes in its commu-
nication facilities, equipment, operations, or procedures
when such action is required. If these changes render the
devices incompatible with the telephone company facili-
ties, the telephone company will provide enough written
notice so that necessary changes can be made in order to
maintain uninterrupted service.
Electrical Specifications
Installation
1. Mount the phone horn to a flat surface using three
mounting screws (not provided).
2. Remove the four #8 X 5/8" (16mm) round head Phillips
screws and remove the phone horn cover.
3. Insert the telephone line through the weatherproof
connector and tighten the connector. Wire the phone
horn as shown in Figure 2.
4. Replace the phone horn cover and secure with the
screws removed in Step 2.
5. Plug the phone horn into a 120V AC outlet.
6. Test the phone horn by dialing the appropriate number
or extension.
Relay
Activation Bell Bell
Cat. No. Voltage Voltage Current (A)
B-KHP-8010-N5 10-250V AC 120V AC 0.15
16-70 Hz 60 Hz
10-150V DC
Figure 1. Phone Horn Dimensions
Maintenance
If this product should fail to operate, disconnect it from
the telephone line and determine if the problem is in the
telephone line or the device. If this product is defective,
discontinue its use and obtain a replacement.
P-047550-1608 ISSUE 4 © 2001
CHESHIRE, CT 203-699-3300 FAX 203-699-3365 (CUST. SERV.) 203-699-3078 (TECH SERV.)
CAUTION
This unit is not serviceable or repairable. Should the
unit fail to operate, contact the supplier for
replacement.
(2 pages)
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels