Edwards-signaling INT-05 Series Manuel d'utilisateur télécharger pdf

www.edwardssignaling.com

Safety Expansion Relay

INT-05-024

INT-05-120

INT-05

TUV Notes:

1. Relay conforms to Pollution Degree II, meets EN1760-1:1998, and must be installed

in an IP54-type enclosure.

2. The wire insulation of connected devices must be rated for 250VAC. The relay meets

basic insulation requirements only.

3. Input devices must meet requirements of EN60947-5-1.

4. The relay must be connected to a primary disconnect device that meets the

requirements of EN60947-3.

5. Controller meets IP20.

6. Test system before operation and after machine maintenance. Controller does not

require maintenance.

7. The complete system should be tested weekly. If a fault occurs, contact

Sentrol Industrial.

8. To be used in conjunction with INT-03 or INT-04.

The INT-05-024 or INT-05-120 Expansion Safety Relay is intended for use as part of a

safety circuit. It provides three additional safe output contacts when used with the

INT-03 Safety Monitor Relay or INT-04 Emergency-Stop Safety Relay.

The INT-05 uses positive-guided relays along with feedback contacts to the INT-03 or

INT-04 safety relay to prevent machine start-up in the event of a component failure.

Voltage to the INT-05 is switched thru the contacts of the INT-03 or INT-04. If a

component failure occurs, the feedback loop to the

INT-03 or INT-04 prevents machine restart.

Description

Installation

1. Mount the relay on a 35mm DIN rail or panel. See

Dimensions

2. Connect the wiring for the switches and relay. See

Wiring Diagrams

. (For proper

operation, DO NOT jumper terminal 1 to terminal 2. Use a momentary button.) For

floor mat applications, connect the two floor mat loops from terminal X1 to X2 and

from Y1 to Y2.

Caution! The relay is available in either a 24 VDC, 120 VAC, or 230 VAC model.

Make sure correct model is used before

applying power.

3. Use one of the following methods to energize the relay:

• For E-stop installations, close all E-stop button contacts and monitored contacts,

and then press the START button.

• For floor mat installations, press the START button without an object on the mat.

Note: The INT-05 must be wired as shown as the unit on its own does not fulfill any

safety requirements.

Dimensions

Slot for 35mm

DIN rail mount

2.46"

6.25cm

1.48"

3.75cm

4.53"

11.5cm

2.95"

7.5cm

2.17"

5.5cm

0.26"

0.66cm

INT-05 __________

Integrity Series

P/N 1030524 • REV D • REB 20MAR13

1 2

Résumé du contenu

Page 1 - Integrity Series

www.edwardssignaling.comSafety Expansion RelayINT-05-024INT-05-120INT-05TUV Notes:1. Relay conforms to Pollution Degree II, meets EN1760-1:1998, and m

Page 2 - Typical Wiring Diagram

Ordering/Electrical SpecificationsPART NUMBER POWER INPUT (L1, L2) INPUT FUSE REQUIREDINT-05-024124VDC +/-15% Fast acting 1/4A (250V, 5 x 20mm, F)INT-

Commentaires sur ces manuels

Pas de commentaire

Edwards-signaling INT-05 Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Edwards-signaling INT-05 Series. Edwards Signaling INT-05 Series User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Edwards-signaling INT-05 Series