Edwards-signaling 871P Manuel d'utilisateur télécharger pdf

870P and 871P Panel Mount AdaptaHorn

Installation Sheet

Description

The AdaptaHorns are UL listed vibrating horns. They are

panel mounted, low current, high decibel horns designed for

heavy-duty use indoors. The horns are intended for general

signaling applications.

PLC Compatibility

The electrical input load requirements for PLC compatible

signaling devices are listed in Table 1. Signaling devices may

be directly connected to output cards that meet these input

load requirements.

24 VDC electromechanical horns such as the 871P-G1 can

produce transient spikes and should only be used on PLC

output cards that have inherent transient spike suppression.

The Process Control Engineer should consult the PLC

manufacturer when connecting 24 VDC electromechanical

devices to PLCs.

Installation

1. Panel Mounting (Indoor or NEMA 4X, 12, 12K/Outdoor)

Locate device to assure adequate spacing to other

components. For live components at 250V or less, the

recommended spacing is 1 1/4" (32mm) from device to

live components mounted on the same surface and 1/2"

(13mm) minimum between device and dead metal

components other than mounting surface, unless

otherwise dictated by local authorities, responsible design

practices, or higher voltages.

Place the mounting template (Figure 1 on page 2), or the

supp

lied trim gasket (do not remove protective backing),

against the mounting surface. Mark and drill the mounting

holes, and device clearance/wire entrance hole. For

NEMA Type 4X, 12, 12K and outdoor applications,

mounting must be to a smooth, flat surface of a NEMA

Type 4X, 12, 12K enclosure or outdoor rated panel and all

four mounting holes must be drilled.

2. Box Mounting (Indoor Only)

Select and install a standard 4" (102mm) square box.

Note: See device label for voltage specifications.

3. Route power source wiring. Connect incoming wires to

the supplied (female) connector assembly using wire nuts

(not supplied).

870P AC models have (2) black and (1) green ground

wire. Polarity is not important.

871P DC models have a positive red lead, a negative

black lead and a green ground lead. Polarity is important.

4. This device is supplied with an adhesive backed trim

gasket. Remove the paper backing and apply adhesive

side to back of unit. Use gasket when mounting the unit to

an outdoor panel or for NEMA Type 4X or 12, 12K

applications, or whenever extra sealing is desired.

5. Plug the male connector (on the device), into the female

connector.

6. NEMA 4X, 12, 12K/Outdoor Mounting: Position the

device onto the surface and secure using (4) #8-32

countersunk head thru-bolts, lockwashers and nuts

(supplied).

Indoor or Box Mounting: Position the device on the

surface and secure using (2) #8-32 countersunk head

thru-bolts, and nuts (when mounting to a panel). The (2)

unused holes can be plugged with (2) #10-32 thread

forming countersunk head bolts or can be used to further

secure the device using (2) additional #8-32 countersunk

head thru-bolts, and nuts (when mounting to a panel).

7. These devices have a volume adjustment set screw

(located on the grille front) which is factory set at the

maximum level. To reduce volume level, turn set screw

clockwise using the supplied 1/16" allen wrench.

Table 1: PLC Compatibility

Catalog number 870P-N5 871P-G1

Operating voltage 120 VAC 24 VDC

Maximum off state

leakage current

25 mA 25 mA

Continuous on current 125 mA 160 mA

Surge (inrush/duration) 1.02 A/0.000026 ms 1.7 A/0.000042 ms

1 2

Résumé du contenu

Page 1 - Installation Sheet

870P and 871P Panel Mount AdaptaHorn Installation Sheet Description The AdaptaHorns are UL listed vibrating horns. They are panel mounted, low curre

Page 2 - Contact information

Figure 1: Template for Panel Mounting Specifications Voltage Current 870P-E5 870P-G5 870P-N5 870P-R5 871P-E1 871P-G1 871P-J1 871P-P1 871P-

Modèles reliés 870P

Commentaires sur ces manuels

Pas de commentaire

Edwards-signaling 871P Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Edwards-signaling 871P. Edwards Signaling 871P User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 870P

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Edwards-signaling 871P