Edwards-signaling 97DF Manuel d'utilisateur télécharger pdf

Installation Instructions for Catalog Series 93, 93DF, 94,

94DF, 97 and 97DF AdaptaBeacon

Signals

Description

The catalog series 93, 94 and 97 AdaptaBeacon signals are UL

and cUL listed strobe lights suitable for indoor or outdoor (weath-

erproof) installation. A hardware kit is included with the 97 series

signals for direct surface mounting applications.

The 93 and 94 series are ac powered; the 97 series signals are dc

powered. These signals are also available in double flash ver-

sions (denoted by DF in the catalog numbers). Voltage and cur-

rent ratings for all models are shown in Electrical Specifications.

Replacement Parts for the signals are available. Refer to Table 1

for details.

Electrical Specifications

1. Disassemble the signal using one of the following applicable

procedures.

a. 93 and 97 Series: Refer to Figure 1. Except for the

voltage ratings, the 93 and 97 series are identical.

Remove the three screws from the skirt, grasp the lens

and lift the lens/skirt straight up off of the base. Then,

remove the three screws holding the strobe tube support

plate to the signal base; grasp the socket (on the strobe

tube support plate) and carefully lift the support plate

off of the signal base. Proceed to step 2.

b. 94 Series: Refer to Figure 2. Remove the three screws

and the rubber gaskets (washers) holding the protective

dome to the signal base. Lift the dome and its rubber

gasket straight up off of the signal base. Then loosen

the three screws in the keyhole slots in the base of the

lens, turn the lens clockwise and lift it off of the strobe

tube support plate. Next, remove the three screws holding

the strobe tube support plate to the signal base; grasp

the socket (on the strobe tube support plate) and carefully

lift the support plate off of the signal base. Proceed to

step 2.

2. The 93 and 94 series signals are conduit mounted. The 97

series can be conduit mounted or direct surface mounted.

Install the signal base using one of the following applicable

procedures.

Installation

WARNINGS

To prevent electrical shock, ensure that power is

disconnected before installing the signal.

To prevent leakage and potential electrical shock,

use care when disassembling the signal to prevent

tearing of the permanently affixed gaskets provided

for weatherproofing.

Catalog Rated Current

Number Voltage

93(*)-N5 120V 50/60 Hz 0.10 Amp

93(*)-R5 240V 50/60 Hz 0.05 Amp

93DF(*)-N5 120V 50/60 Hz 0.10 Amp

93DF(*)-R5 240V 50/60 Hz 0.05 Amp

94(*)-N5 120V 50/60 Hz 0.10 Amp

94(*)-R5 240V 50/60 Hz 0.05 Amp

94DF(*)-N5 120V 50/60 Hz 0.10 Amp

94DF(*)-R5 240V 50/60 Hz 0.05 Amp

97(*)-EK 12 - 48V DC 1.20 Amp

97(*)-MP 75 - 125V DC 0.20 Amp

97(*)-S1 250V DC 0.10 Amp

97DF(*)-EK 12 - 48V DC 1.20 Amp

97DF(*)-MP 75 - 125V DC 0.20 Amp

*The letter (A - amber, B - blue, C - clear, G - green, M -

magenta or R - red) in this position signifies the color the

supplied lens.

CAUTIONS

To prevent damage to the strobe tube, lift the lens

straight up and off of the signal.

To prevent damage to the strobe tube, handle the

strobe tube only by the base.

WARNINGS

To prevent leakage and a potential shock hazard,

when mounting outdoors the signal must be

installed with the lens or dome facing directly up.

Conduit Mounting

a. Route the field wiring from the appropriate power source

for the signal through 3/4" (19 mm) NPT conduit and

through the conduit entrance hole in the signal base.

Refer to Figure 1 for the 93 and 97 series signals and

Figure 2 for the 94 series.

b. Install the signal base on the conduit and proceed to step

Cheshire, CT 06410 203-699-3300 (Ph)

203-699-3365 (Cust. Serv. Fax)

203-699-3078 (Tech. Serv. Fax)

1 2 3 4 5

Résumé du contenu

Page 1 - CAUTIONS

Page 2 - P-047550-0943 ISSUE 7

P-047550-0943 ISSUE 7Direct Surface Mounting (97 Series Signals Only)a. Remove the three outer knockouts from the bottom ofthe signal base. The loca

Page 3

P-047550-0943 ISSUE 7Figure 3. Mounting Gasket for Direct Surface Mounting of97 Series SignalsFigure 4. Direct Surface Mounting of 97 Series Signal

Page 4 - Table 1. Replacement Parts

P-047550-0943 ISSUE 7Catalog orComponent Used On Part NumberXenon Strobe Tube All series 92-STDome (Clear) 94 Series 94-DCLens (Amber, Blue, Clear, G

Page 5 - Approved by: KRT

ECN: 03-C1662Issue: 07File: FCF120Approved by: KRTP-047550-0943 OFFSET SPECINSTALLATION INSTRUCTIONS FOR CATALOGSERIES 93, 93DF, 94, 94DF, 97 AND 97DF

Modèles reliés 97 | 94DF | 94 | 93DF | 93 |

Commentaires sur ces manuels

Pas de commentaire

Edwards-signaling 97DF Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Edwards-signaling 97DF. Edwards Signaling 97DF User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 97 | 94DF | 94 | 93DF | 93 |

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Edwards-signaling 97DF